There are many different installations that were used for the different Cessna models. Please consult your applicable Service/Maintenance Manual and Illustrated Parts Catalog for the proper location for your specific aircraft.

We sell tool P/N 970 to facilitate the installation of the aft rollers and make the installation easier and simplified for this hard to reach location.

The handle of the tool makes access to the bolt hole in the small inspection opening easy. The pointed tool allows you to align the parts and easily insert the tool in the bolt hole. The next step is to push the tool back out of the hole with the bolt.

The Cessna Service Bulletin SEB95-3 describes damage to the flap support arms from the edges of the rollers cutting into them as the flap rollers rotate. Cessna fixed the roller end wear problem on the forward roller locations by installing a thin stainless steel wear washer between the roller and the flexible flap arms.

The aft roller location is more difficult as it is up in the flap structure and is rigid. The flap support arms will not flex open for the addition of wear washers like the forward roller location. The aft long roller position has the same wear problem as the forward roller locations. Since there is not room to install a wear washer with the existing roller, McFarlane designed a roller slightly shorter in length that allows room for wear washers on each end of the roller. The wear washers are designed with a step in them to make them an assembly that is easier to install.

Note that the upgrades do not change the aft narrow roller and shims/spacers that control the flap lateral end play. P/N MCSK100 only replaces the unprotected long aft roller(s) on each flap. Replacing the flap arms that have excessive wear is very expensive and time consuming. MCSK100 stops any further flap support arm wear.

Flap Roller Kits contain all of the rollers needed to complete one aircraft. Flap Roller Upgrade Kits include all of the components, forward wear washers (P/N MCS1450-3S10-032), aft service kit (P/N MCSK100), and hardware needed to replace the flap rollers and hardware associated with the rollers, along with Cessna SEB95-3 Rev. 1 for instructions to inspect flap support arms for wear.

P/N MCSK100 Flap Roller Service Kit replaces the aft wide roller assembly, and only the aft wide roller. Please consult your applicable Service/Maintenance Manual and Illustrated Parts Catalog for the proper location for your specific aircraft, and the STC SA01074WI.

A universal joint attaches to each control yoke shaft behind the instrument panel. Universal joints are very precision. Replacement of the universal joint is required if any free motion or rust around the joint pivots is detected or if the joint fails inspection required by the Piper AD 2010-15-10.

Clean the barrel and screw jack and re-apply a coating of MIL-PRF-23827 low temperature grease. The cam bushings that attach the jack screws must be properly adjusted so that both jack screw work as one unit. If the cam bushings are not adjusted correctly the jack screws can work against themselves causing a hard to turn situation. Please review the complete instructions.

The trim wheels on the Cessna 180, early 182 and 185 aircraft have a spring loaded trim wheel stop catch assembly that engages with a molded in ratchet on one side of the trim wheel. This system is designed to prevent unwanted trim wheel movement caused by air pressure on the horizontal stabilizer. If these stop catch assemblies are worn out, the trim wheel is free to rotate. McFarlane has replacement stop catch assemblies.

There are advantages to both, see our article on this topic: Stainless Steel or Galvanized Steel Cable?

No, the fuel indicating system on a Cessna 152 is unique and McFarlane has not designed a transmitter for them yet.

Yes. The fuel screen is removed by removing the standpipe. The rubber tipped plunger must be unseated before the standpipe is loosened. Failure to lift the plunger off of its standpipe seat can damage the plunger. Pull the strainer drain knob as if you were draining the fuel bowl. Block or clamp the knob in this position. Insert a smooth round tool such as a screw driver or punch in the standpipe cross-hole and un-screw the standpipe.

Yes, please review the Installation Tips for McFarlane Fuel Vent Lines.

The fuel selector valve works in unscreened fuel. Contaminated fuel can cause selector valve seal damage. When fueling from possibly contaminated fuel sources McFarlane recommends the use of a fuel filter, such as Mr. Funnel or another filtering device, to reduce trash in the fuel system.

The most common indication of external fuel valve leaks is the smell of avgas in the cabin. Most valves are located under the cabin floor. Fuel stain on the valve and drain plug or drain valve or on the belly of the aircraft can also indicate external leakage. External leaks are generally around the actuation valve stem. Internal leaks are detected when the fuel is turned off and fuel continues to drip during fuel system maintenance. Inner port leakage will allow fuel from one tank to leak into another fuel tank. This type leak is difficult to detect. Fuel transfer from one tank to another with the fuel valve selected to one tank only will indicate inner-port leakage. An extended period of time is needed to detect fuel transfer from one tank to another. Generally if internal leakage is detected when servicing the fuel system, it is likely there is also inner-port leakage. 

Curtis Superior and SAF-AIR valves are designed for installation in a standard NPT port for NPT threaded valves or an AND-10050 style port for UNF threaded valves. Use a thread sealant or Teflon tape on pipe threaded valves. Never allow any thread sealant on the first thread . This will prevent contamination of the fuel system. Refer to aircraft manufacturer's torque specifications for the aircraft in which it is being used.

Replace the rubber seals as per the aircraft manufacturer’s recommendations or every ten years when no guidance is given. McFarlane stocks replacement seals and seal kits for both Curtis Superior and SAF-AIR valves. The new Curtis valves use a O-ring type seal instead of the flat seal that was previously used. 

SAF-AIR valves are designed to be disassembled and the O-rings replaced. Over time, if the valve should start to leak, check to make sure the drain valve is tight. If drain valve is found to be tight, then check the O-rings. All O-rings used are buna "n", MS29513 Style, MIL-P-5315. SAF-AIR O-ring seal kits are available for most of their valves. Add a "K" or "-K" suffix to the valve part number.

Never have a hose attached in flight to the oil drain valve. Engine vibration and the additional attached mass can cause premature seal and valve wear which could result in valve failure and a loss of engine oil.

A common cause for this problem is fuel starvation due to improper installation of the fuel pump. Make sure that the fuel lines are not crossed; that is, the inlet line should be connected to the inlet side of the pump (marked “IN” on the top of the port) and the outlet line should be attached to the fuel pump outlet port. Fuel should be present at the inlet side of the fuel pump.

Improper installation of the fuel pump may result in a misalignment of the operating lever with the operating plunger in the accessory case. If so, there will be no movement of the lever and no pumping motion to provide fuel flow. If misalignment is found upon removal of the pump, the lever is probably damaged or broken. If misalignment of the operating lever has occurred, it will require inspection and repair by a qualified technician.

There are several other components in the fuel indicating system which could be the issue or are causing the indication problems:

• Ensure that your aircraft fuel indicating system utilized Stewart Warner style transmitters.
  • Even if your aircraft originally came with that style, there were many Cessna Service Bulletins to replace them with the Rochester style. Our transmitters will not work with those components if they have been changed. This was a very common SB when Cessna switched over to Rochester. 
  • Transmitter Identification shows the difference in the Rochester style and the original Stewert Warner transmitter.
  • McFarlane transmitters and Cessna Stewart Warner transmitters have an electrical resistance range of about 32 ohms when in the full position and 250 ohms in the empty position. This can be measured with an ohm meter connected between the wire terminal and the metal body. Note that the gold dichromate corrosion treatment on the zinc plating is a poor conductor. The metal body must be scratched a little to get a good electrical connection. The Rochester transmitter has a much different resistance pattern than the Stewart Warner or McFarlane transmitter.
• Consult your log books and check the part numbers of the fuel gauges and transmitters. Do not rely on Illustrated Parts Catalog or eligibility.
• With the age of most of the general aviation fleet, the possibility of corrosion in the wires or grounding is very likely. The gauge (indicator) may not be working correctly or properly calibrated. 
  • Since the transmitter gauge system works with very low voltage and very low milliamp electrical flow it is very sensitive to proper grounding and high resistance in electrical connections. Most problems are related to electrical connections.
  • Excess resistance in the transmitter circuit can be detected by measuring the transmitter resistance with the transmitter being installed but without the wire connected at the terminal, and then measuring the resistance at the transmitter wire at the back of the gauge with the transmitter wire connected to the transmitter terminal and the transmitter wire disconnected from the fuel gauge and the other ohm meter connection to a ground at the back of the gauge. The resistance readings should be very close to the first resistance reading. In other words, you are measuring the transmitter resistance first without the airplane circuit and then comparing the reading with the airplane electrical circuit.
  • If the preceding wiring check shows good, the problem is likely in the gauge. The fuel gauge has a brass grounding strap that grounds the internal electrical coils to the gauge case. With years of service this grounding strap can develop a thin layer of corrosion that restricts electrical flow. When this happens the gauge will show more fuel than what is in the tank which is not good! Cleaning this ground strap should fix the problem. Refer to the Cessna service manuals for detailed trouble shooting and maintenance information.

Caution! Never short the battery power to the transmitter wire! It will take only seconds before the stainless steel resistance wire in the Cessna transmitter will glow red hot in the fuel tank. The hot wire could explode the tank! Never have power on when trouble shooting the fuel gauging system.

Electricity in the Fuel Tank. Is it Safe?

Always check the fuel gauge system for proper calibration per the Cessna maintenance instructions.

Do you have aftermarket Monarch fuel tanks installed? We have received customer feedback stating that when Monarch or other aftermarket fuel tanks are installed, McFarlane’s fuel vent line does not fit. There is nothing we can do to solve that issue. McFarlane’s fuel vent lines fit well when OEM fuel tanks are installed. Please review the Installation Tips for McFarlane Fuel Vent Lines.

Diaphragm fuel pumps should be replaced or overhauled:

1. At engine TBO or after ten years in service, whichever occurs first. Replace on condition if leaks develop or performance drops for example.
2. Refer to Lycoming Mandatory Service Bulletin 240W for information regarding engine TBO.

The Viton gasket and screw seals do not require any sealer and must not have any lubricants. Do not over tighten the attachment screws as over tightening can extrude the gasket out from under the transmitter and tear the gasket in the screw holes. This will cause a leak. Tighten the screws evenly until you see the gasket just start to extrude a little. Any lubrication will aggravate the tearing of the gasket.