Typically Tempest spark plug resistors will stay between 1000 and 1500 Ohms throughout their life. Tempest specifies that the plug resistor should never be below 500 Ohms or above 5000 Ohms. We offer a lifetime guarantee on our fired-in resistor.

Tempest oil filters use media with a 40-micron rating.

Tempest currently manufactures only 18mm spark plugs.

Yes, you should rotate your spark plugs every 100 hours. This will help even out electrode wear caused by constant polarity and capacitance after-fire. Place them in a Tempest spark plug tray (P/N T240) and follow the rotation guide supplied on every Tempest spark plug box.

We can only speak for Tempest overhauled pumps as we have no control over the quality of other overhaul shops. Before Tempest®/Aero Accessories, LLC offered an overhauled pump, they spent more than a year in research and testing to determine what was required to produce a quality overhauled pump that would last as long as a new pump producing the vacuum or pressure required for aircraft application. In 1984 Tempest®/Aero Accessories, LLC had its overhaul process specification approved by the FAA and began offering quality overhauled vacuum pumps to general aviation. Tempest takes great pride in their state of the art overhaul facility, and produce the best overhauled pump on the market today. Over the years they have acquired FAA-PMA’s for all component parts of the Dry Air Pumps, and have supplied replacement parts to all overhaulers worldwide.

Always refer to the engine manufacturer’s recommendation. If no recommendation is made then we suggest you replace Tempest oil filters every 25 to 50 hours.

Height. Over the years aviation oil filters have gotten shorter to help with installation in tight spaces. The dash two filter by Tempest is the shortest of the certified aviation oil filters on the market.

Yes, all Tempest aviation oil filters use a magnet. This give us an extra layer of defense to help filter out smaller micron particles that may get past the filtration media.

Tempest created the Spin EZ oil filter to make installation and removal easier and more efficient. A patented solid seal lubricant is applied to our oil filter gasket during manufacturing and requires no oil or DC4 compound prior to installation; making the removal process of a stuck filter a thing of the past.

Please visit the Technical Data portion of our website to find our articles on best cleaning practices.

Indicated by hard ash-type deposits, lead fouling can be caused by poor fuel vaporization due to cold operating temperatures or high-lead content in the fuel (misdistribution of tetraethyl lead). Lightly fouled plugs can be cleaned, re-gapped, tested and reinstalled using a new copper mounting gasket. Severely fouled plugs should be replaced with new Tempest® spark plugs.

Both short and tall filters are approved for most engine applications. Determining which height filter to use all depends on the space you have inside the engine cowling. We suggest going with the taller of the approved oil filters if you have the space.

Note: Tempest’s replacement recommendation is the same for both short and tall filters.

First, the firing end of the plug must be cleaned of lead, carbon and oil. Once cleaned you can use the Tempest AT5K® or a multi-meter. If using an AT5K please see the tool section of our website. If using a multi-meter place one lead on the center electrode and the second lead on the contact point inside the spark plug terminal well. Be sure that your multi-meter is set to the correct setting.

Please refer to the Tempest application chart. There are several things you will need to know as most engines have several different spark plugs approved.

1. You will need to know your harness B-nut size. This is the nut that screws onto the spark plug. It will be either a 5/8-24” or ¾-20 thread. Be aware that a 5/8-24 utilizes a 3/4” wrench and a ¾-20 utilizes a 7/8” wrench.
2. Long reach v. short reach will be determined by the specific engine.
3. Heat rating is indicated by the numeric value of the spark plug part number. The lower the numeric value the colder the heat rating. Best practice is to use the same heat rated plug you have removed.
4. Massive electrode or fine wire is a personal choice. Massive plugs will generally operate 400-500 hours. Fine wires can last 1500 hours. This choice is usually determined by number of annual hours flown and the size and performance of the specific engine.